End Suction Pumps

  • An XA Series End Suction Pump
  • An AQU Series pump cross section.
  • A KTG Series pump cross section.
  • A 9 inch water truck pump schematic.
An XA Series End Suction Pump
An AQU Series pump cross section.
A KTG Series pump cross section.
A 9 inch water truck pump schematic.

XA Series Flex-Coupled End Suction

The XA flex-coupled end suction product line is one of the most common and versatile centrifugal pumps used in a variety of markets in the industry, such as HVAC and building trades markets. Whether you are pumping clean water, high temperature condensate or raw water, the robust and highly engineered XA Series is up to the task. Each model features 250# cast dimensional flanges, integral suction vortex suppressor, 420 stainless steel shafting, investment cast 304 stainless steel impeller and an oil lubricated power frame.

Performance Specifications

  • Flows To: 24,000 GPM (5,500 m³/hr)
  • Heads To: 450 Feet (140 m)
  • Temperatures To: 350ºF (177ºC)
  • Speed Ranges: 900 RPM To 3600 RPM
  • Size Range: 1.25×2-5 (32/13) – 28×32-24 (700/60)

Features

  • Cast iron casing/investment cast 304 stainless steel impeller
  • Back pump out vanes or rear wear ring standard for hydraulic balancing
  • Back pull out rotor assembly design
  • Standard bronze, renewable case wear ring
  • Internal plan 1 seal/packing flush
  • Mechanical seal standard with packing & lantern ring as an option
  • Francis, enclosed, high efficiency impeller with broad band operating range
  • 125# suction/125# discharge flange with 250# cast dimensions standard
  • Drilled & tapped suction & discharge flanges for easy connection to system piping
  • Suction & discharge gauge connections standard
  • 50,000+ hour minimum L10 bearing life standard
  • Turned, ground and polished 420 stainless steel shaft standard
  • Oil lubricated power frame with grease lubricated as an option
  • Dual oil lip seal construction with bearing isolators as an option

Available Metallurgies

  • Cast iron, ductile iron, all bronze, 304 stainless steel fitted, 316 stainless steel fitted

DOE Requirements

This product is not confirmed as meeting 2020 DOE standards and is available for sale only in Fire Pump packages and/or outside of US/CAN


AQU Series Close-Coupled End Suction

The AQU close-coupled end suction product line is one of the most common centrifugal pumps used in the industry today in markets such as HVAC and building trade. Whether you are pumping clean water, high temperature condensate or raw water, this robust and highly engineered product line is versatile and up to the task. Each model features 250# cast dimensional flanges, integral suction vortex suppressor, 420 stainless steel shafting and investment cast 304 stainless steel impeller. The AQU product line uses an exclusive design that allows for easy coupling to a stocked, standard C-face motor.

Performance Specifications

  • Flows To: 9,000 GPM (2,440 m³/hr)
  • Heads To: 450 Feet (140 m)
  • Temperatures To: 250ºF (121ºC)
  • Speed Ranges: 900 RPM To 3600 RPM
  • Size Range: 1.25×2-5 (32/13) – 12×14-16 (300/40)

Features

  • Cast iron casing/investment cast 304 stainless steel impeller
  • Back pump out vanes or rear wear ring standard for hydraulic balancing
  • Back pull out rotor assembly design
  • Standard bronze, renewable case wear ring
  • Internal plan 1 seal/packing flush
  • Mechanical seal standard with packing & lantern ring as an option
  • Francis, enclosed, high efficiency impeller with broad band operating range
  • 125# suction/125# discharge flange with 250# cast dimensions standard
  • Drilled & tapped suction & discharge flanges for easy connection to system piping
  • Suction & discharge gauge connections standard
  • Turned, ground and polished 420 stainless steel shaft standard
  • Utilizes, stocked, standard C-Face motors
  • 56C through 449TC brackets for coupling to drivers

Available Metallurgies

  • Cast iron, ductile iron, all bronze, 304 stainless steel fitted, 316 stainless steel fitted

DOE Requirements

This product is not confirmed as meeting 2020 DOE standards and is available for sale only in Fire Pump packages and/or outside of US/CAN.


KTG Series Vertical Inline End Suction

The KTG vertical inline end suction product line is one of the most common centrifugal pumps used in the industry today. This product line is very versatile and is used in a variety of markets such as HVAC and building trade due to it’s inline suction and discharge connection, that allows for an easy install anywhere within existing piping. Each model features 250# cast dimensional flanges, integral suction vortex suppressor, 420 stainless steel shafting and investment cast 304 stainless steel impeller. The KTG product line uses an exclusive design that allows for easy coupling to a stocked, standard C-face motor.

Performance Specifications

  • Flows To: 9,000 GPM (2,440 m³/hr)
  • Heads To: 450 Feet (140 m)
  • Temperatures To: 250ºF (121ºC)
  • Speed Ranges: 900 RPM To 3600 RPM
  • Size Range: 2×2-5 (50/13) – 14×14-16 (350/40)

Features

  • Cast iron casing/investment cast 304 stainless steel impeller
  • Back pump out vanes or rear wear ring standard for hydraulic balancing
  • Back pull out rotor assembly design
  • Standard bronze, renewable case wear ring
  • Internal plan 1 seal/packing flush
  • Mechanical seal standard with packing & lantern ring as an option
  • Francis, enclosed, high efficiency impeller with broad band operating range
  • 125# suction/125# discharge flange with 250# cast dimensions standard
  • Drilled & tapped suction & discharge flanges for easy connection to system piping
  • Suction & discharge gauge connections standard
  • Turned, ground and polished 420 stainless steel shaft standard
  • Utilizes, stocked, standard C-Face motors
  • 56C through 449TC brackets for coupling to drivers

Available Metallurgies

  • Cast iron, ductile iron, all bronze, 304 stainless steel fitted, 316 stainless steel fitted

DOE Requirements

This product is not confirmed as meeting 2020 DOE standards and is available for sale only in Fire Pump packages and/or outside of US/CAN.


9″ Water Truck Pump

  • Volute: Heavy cast iron construction. Back pullout design. Can be rotated for ease of installation.
  • Impeller: Cast iron enclosed design for high efficiency. Double keyed for improved reliability.
  • Seal: Packed box or mechanical seal with carbon/ceramic faces, BUNA elastomers and 300 series stainless components.
  • Bearing Frame: Heavy duty iron, oversized shaft, max-life bearings and external grease lubrication.
  • Mounting: Can be mounted in vertical or horizontal position.
  • Standard and hydraulic fit

Maintenance Features

  • Replaceable shaft sleeve
  • Grease fittings for lubrication
Franklin Electric Logo